malo225

The breaker who sold me the clocks has sent me a module untested for me to try free of charge I've just ordered a new loom for the rear sensors as it's damaged at two of the plugs eBay 10 pounds If you pm me your address or email me it I'll donate mine to you Any chance you can tell me where you got the bits for the bonnet mod I read on another post

Whoo bloody hoo i have just fixed the fault Terminal 28( Green white )comes from the VSS on the gearbox voltage 0 or 12 Terminal 3 (Purple )on the cluster socket goes to the ECU parking module temp gauge speed control i was getting 0.50 Vdc max disonnected the wire on the cluster at terminal 3 and got 12v at the terminal found after a lot of checks the voltage was sinking from this terminal disconnected the parking module and the fault has cleared will take out of the car tomorrow Does any one know if these can be repaired Mirez Thanks for the assistance

hello thanks for looking at this i have a problem with my car se post below http://www.fordgalaxy.org.uk/ford/index.php?showtopic=22308&st=15 please has anyone got the specific wiring for the ecu plug im looking for the signal for the speed sensor from the instrument cluster i have ford tis-- tolerance data but block diagrams are a nightmare my email addrss is malo225@hotmail.com if you are able to send any help/diagrams etc many thanks mark

Mirez ive fitted another set of clocks guesss what same fault have managed to get the ecu out its the vw part 7M5-906-022K ford part YM2A-12A650-FD Im going to check the wiring to make sure i have continuity betwwen the the speedo and ecu if thats ok i think that the ECU needs repiaring can you suggest a company i spoke withh BBA Reman and we are looking at

Comm error a red herring When I took the cluster out and started the car it must have come up I tried it again and the same fault has come up Measuring blocks Cluster I can see speed if I drive it when plugged in ( only on the drive though) also Abs I can see individual speeds but I cannot access the ecu what module should it be Thanks mark

Hi 03. ABS brakes No Faults Does the abs send a signal for speed to the instruments then to the ecu

hello Cable came today and ive managed to connect it to the cra with VCDS lite it has connected to the insruments and come up with 01316 ABS control module 49-10-No Communications -Intermittent parkings sensors nothing at all the pipe for the rear wash came off soaked the foot well so I think its naffed what do you think also could not do full scan as shareware version thanks again mark

Hello Mirez have I ordered the right cable Thanks mark

If the signal is derived from the cluster Could it be that it is faulty I have unplugged it and checked the cables and plugs they all look ok I have the ford TIS cd and can see the path that the cable takes from the sensor to the cluster I have just ordered a obd2 409.1 kkl interface from eBay Is that the right one

Another thank you Can you recommend a k line interface please

Hello Mirez I can clear it with the engine check software now and again the Engine management light comes on and goes back off a couple of days later. Any ideas why I can't see any speed data Interesting that you say speed signal would not stall the car as I've been told the speed signal controls the idle control valve The latest thing I've been told is to replace the speedo clocks as The signal goes to the clocks then to the ECU Thanks for your help

Thank you for your reply I am an electrician so the first thing I did after replacing the sensor was to check all the wiring through the engine loom right back to the junction Behind the battery the fact that the speedo works tells me the wiring is ok If I unplug the sensor the car drives but the speedo does not If the vag com will not work what system can I get to check problems With the parking sensors etc Thank you

Hello Sorry in advance if post has been covered else where i have a 2001 Galaxy mark 2 Zetec that cuts out at junctions has P0500 speed sensor malfunction fault so far ive been told ECU is faulty --the siganl is not getting to the ECU the instrument cluster is faulty -- but the speedo is working speed sensor fauly ---brand new ford sensor fitted idle control valve sticking ---replaced valve power relay fauly ---R30 replaced clutch switch checked and is working ok i have bought engineckeck software and cable all fuctions RPM OXY etc it shows zero speed this has been confirmed by mobile diagnostic tuning guy tried two types of kit so the fault is no speed Please can anyone shed a light on this any help would be gratefully recieved also tried vag com with OBD2 cable but came up with No Controller Found any ideas with this also please