Galaxy23

Changed the brushes today in the run on pump. It now seems to be working as I can hear a buzzing type noise coming from it when the ignition is on. Also the booster heater is working. I cancelled the old fault codes on my vag com and the heater over temp fault code has shown its ugly head once more and I don't know why it is still showing this persistent fault code. Any ideas please??????

Changed the brushes today in the run on pump------ quite a challenge. Anyway it is now working as it makes a buzzing type sound when the ignition is on. Done a check on the vag com after clearing the old fault codes and it Is still showing heater over temperature as a fault. The booster heater came on and appears to be working. Any ideas why I could still be getting this fault code ? Thanks Paul

I have ordered some brushes from a very helpful person called Keith who works for muchmoreracing.com, contact no 01207 239357. They are modified long life motor brushes and are 5mmx5mmx10mm in size and are

Thanks for the replies> Where can I get the bushes from ? What size do I need and how many ? What fuse do I need to take out ? Thanks, Paul

I haven't checked the pump is running as of yet. Car has done 102k and it is an 05 Tdi Ghia . I think it has the D5Z-F. Don't think my vag com can check outputs as its only a basic one .It.s vs450 vgate scanner. I suspect that it is the run on pump as after clearing the codes and going for a drive the 01410 fault code came up- heater over temp. Do you think this is the likely candidate and that the bushes are worn ? Thanks Paul

Just plugged a vag com into the gal. I now have 3 fault codes for the booster heater: 01413 - Dosing/metering pump (V54) static- short circuit to earth 01410- heater over temp 01492- function lock out 06-00 signal too high I have cleared the fault codes again and the heater has fired up. Might be better if I just clear the fault codes every time What can I check ? Do I need a new dosing pump or is it simply a wiring issue that is causing these faults.

Thanks..... will check the thread

Does anyone know the part no or where to get one from - a booster heater temp sensor that is fitted in front of the pollen filter. I spoke with Ford and they couldn't find the temp sensor on their system How may temp sensors should the galaxy have ? My gal keeps on bringing up a fault code 01410 heater over temp and then its 01409 flame out. I clear the fault code with a vag com and it starts working again. Might be cheaper just clearing the fault codes each time. Would be grateful for any advice. Thanks Paul..

Hello I am selling 2 front wings from a 2004 Seat Alhambra. They are both rust free and have been primed in grey ready for spraying and are in excellent condition. :) If anyone is interested please let me know. They are cluttering the house and have to go. Regards Paul

Thanks.I will ask my mechanic and get back to you.

Mine is a mk 2 seat alhambra tdi on a 54 plate so am not sure of the set up with the pipes ???

Hello My car has a leaking air con pipe.It is the one that runs underneath the air filter and along behind the engine . My mechanic has had a lot of trouble in trying to remove the pipe as there is very little room to manoeuvre it.He has ended up cutting the pipe into sections in order to remove it,but he hasn;t been able to remove the last bit of pipe due to a tight joint.He has sprayed the joint with penetrating fluid in the hope that it will free the pipe from the joint when he carries on with the job next Sunday. Does anyone know how to re-fit this pipe as there is no room apparently to put it back.Surely the engine doesn't need to come out ???? Please can someone help. Regards Paul :rolleyes: :( :(

Many thanks for the reply. My mechanic has sorted it now with some grease on the spindle and a new pipe connecting to the washer jet. :rolleyes: :rolleyes:

Hello My rear washer jet doesn't squirt any water out.I suspect freeze thaw action has disloged a connection in the pipe somewhere. Is there a link on this that shows me how to do the job? I think it's just a case of clipping the hose back together,but i have forgotten where it is located,etc. Also my rear wiper is slow and i suspect that the motor may be on the way out. Any suggestions? Many thanks Paul

Thanks for the replies. Are there any pics available showing how to take dash out ? Thanks, Paul :wacko: